Royal Sovereign Laminator NB 1900N User Guide

OWNER'S MANUAL  
LAMINATOR Model No. NB-1900N  
Read all instructions carefully before use.  
For any customer support needs, please choose  
Royal Sovereign International Inc.  
 
NB-1900N  
INTRODUCTION  
Thank you for purchasing a Royal Sovereign Laminator.  
To insure high quality lamination, please read this instroduction manual thoroughly.  
For additional product support or factory-direct ordering information.  
Call Royal Sovereign Customer Service at (800) 397-1025.  
MAJOR PARTS  
Top Cabinet  
Output  
Power Cord  
Input  
Control Button Panel  
LED  
CHARACTERISTICS  
LAMINATOR NB-1900N is an advanced laminator of contemporary design,  
utilizing the lastest in laminating technology.  
1. Contemporary design and rounded shape will enhance any decor.  
2. A microprocessor is used for added protection.  
1) The microprocessor protects the rollers  
a.Even when power is off, rollers continue to turn until properly cooled down.  
b.In the event of a power failure, rollers continue turning until properly cooled down.  
2) The microprocessor prevents overheating  
If a temperature sensor fails, the microprocessor prevents rollers from overheating.  
3. Designed to prevent heat from radiating through the housing, using powerful fans.  
4. Eight function settings, allow you to laminate various types of film.  
5. Every time a button is pressed, a buzzor sounds.  
6. Temperature is controled automatically for energy efficiency.  
3
 
NB-1900N  
SAFETY PRECAUTIONS  
Failure to comply with any of the following safety procedures could  
result in serious injury. Keep this information for future reference.  
1.To prevent the possibility of fire or injury, do not allow articles  
of clothing (neckties, scarves, or paperclips etc.) inside the  
machine.  
2. Do not attempt to laminate items that exceed total  
recommended material thickness.  
3.To prevent the possibility of electric shock, do not immerse  
the laminator in water or permit liquids inside the machine.  
4. Do not operate machine for any other purpose other than its  
intended use.And do not insert sharp objects into front or rear  
machine openings.  
5. This machine is for indoor use only.  
6. Do not operate the machine if the outlet or power cord is  
damaged. And do not alter the electric plug in any way.  
Contact a qualified electrician.  
7.The electrical outlet should be installed near the equipment  
and should be easily accessible.  
4
 
NB-1900N  
SET UP  
Place laminator on a sturdy, flat work surface. Allow ample clearence  
behind laminator for laminated document or photograph to exit completely  
without bending.  
Connect laminator to an electrical outlet that matches laminator's rated voltage  
and power requirements.  
If an extension cord is required, use a cord rated higher than the laminator's  
capacity.  
CONTROL PANEL SETTINGS  
Eight Functions allow you to laminate as necessary.  
TACT-BUTTON and LED were designed for your convenience.  
1.FUNCTION OF BUTTONS  
: Increase setting  
TEMP  
: Decrease setting  
COLD  
COLD  
: COLD Function  
ON/OFF  
ON/OFF  
: Power On/off  
2.DISPLAY  
NB-1900N  
200~250 micron (8~10 mil) film, color foil and  
mount board laminating  
150~180 micron (6~7 mil) film laminating  
80~125 micron (3~5 mil) film laminating  
Cold film laminating  
5
 
NB-1900N  
3.INSTRUCTION OF BUTTONS AND LED  
1. Press power button to turn laminator on or off.  
2. When you press power button, "FUNC 2"  
LED is blinking. At this time, function buttons  
become available.  
NB-1900N  
3. To choose film thickness, press  
or  
and you will see the LED read-out.  
COLD  
4. For cold laminating, press  
LED will light up.  
then green  
5. When you choose any function, a blinking LED light  
means it's not ready. When the blinking stops, the  
laminator is ready.  
TEMP  
6. When blinking stops, a buzzer will ring once every  
two minutes.  
COLD  
7. Even if you turn off as soon as finishing laminating,  
rollers will continue to turn until cooled down properly,  
and then stop.  
ON/OFF  
6
 
NB-1900N  
HOT LAMINATING  
1. Press the power button.  
2. Choose setting by  
or  
3. When red LED stops blinking and buzzer rings, you're ready to laminate.  
(It takes 4~5 minutes depending on setting function.)  
4. Put document to be laminated, into a laminating pouch. Leave a minimum  
border of about 3mm(1/8"), to provide a proper edge seal.  
5. Insert pouch squarely into opening slot.  
6. Finished lamination will exit through rear of machine.  
7. Emerging laminated document is hot to the touch.  
(Always allow lamination to cool down on a flat surface for about a minute  
before handling, to prevent permanent bending. If document is not  
laminated well, re-insert it and run it through a second time.)  
8. When continuously laminating, run the laminator at a lower setting  
because the internal machine temperature may be higher than the  
required temperatur, causing the document to bend or ripple.  
9. When finished laminating, turn off the machine.  
'***USEFUL INFORMATION***  
Sometimes, when continuously laminating, LED may begin  
blinking. If this happens, finish laminating the current document,  
then wait until the LED stops blinking, before inserting the next  
lamination.  
* Do not laminate empty or thin pouch on a thick film setting.  
The pouch could stick to the roller.  
* Do not unplug laminator while laminating.  
This could be fatal for the rollers due to the high internal temperature.  
7
 
NB-1900N  
COLD LAMINATING  
1. Press the power button to turn laminator on.  
2. Press  
COLD  
3. It is ready when green LED blinking stops and buzzer rings.  
4. Insert document into Royal Sovereign cold laminating pouch as follows.  
**HOW TO ATTACH DOCUMENT ON COLD POUCH FILM**  
1) Prepare cold pouch film.  
Back  
2) Remove protective paper inside cold pouch.  
(Be careful not to allow the pouch to close and  
seal itself closed. If the pouch closes on itself  
and seals,you will not be able to the document  
to be laminated inside.)  
Front  
3) Place document squarely into the pouch, where  
the protecting paper was.  
Cold film's minimum border of about 3mm(1/8")  
is necessary to provide a proper edge seal.  
4) Beware of dust while inserting document.  
5) Feed pouch squarely into opening slot.  
5. Finished laminated pouch will exit through rear of machine.  
6. When you are finished laminating, press the power button to turn off.  
If it has recently been used for hot lamination, allow the rollers to  
be cooled down about 20~30 minutes.  
8
 
NB-1900N  
COLOR FOIL LAMINATING  
Your laminator has ability to add color by using color foil to documents copied  
or printed by laser printer using toner.  
**PAPER CARRIER is required**  
1. Press the power button to turn laminator on.  
2. Find FOIL setting, using  
3. Machine is ready when red LED stops blinking and the buzzer rings.  
4. Position color foil where you want on the document and insert it into the  
paper carrier.  
5. Insert the paper carrier squarely into the opening slot.  
6. Finished foil laminated paper will exit through rear of machine.  
7. When you are finished laminating, press the power button to turn machine off.  
'***USEFUL INFORMATION***  
The document, which has been foil laminated, is hot and easily  
bent. Try not to touch the document until it has cooled down.  
* When you do laminating several colors, use high temperature tape  
to hold color foils in place.  
* For high quality lamination, choose FUNC depending on thickness of material  
and PAPER CARRIER.  
(Foil laminating temperature is set for a bond paper.)  
9
 
NB-1900N  
MOUNTING BOARD LAMINATING  
**You can laminate photographs or pictures on a mounting board,  
less than 2mm (1/12") thick without any tension adjustment.**  
1. Press the power button to turn the machine on.  
2. Set FOIL setting with  
3. When the LED light stops blinking and buzzer rings, the laminator is ready.  
4. Place material on Mounting board.  
5. Insert Mounting board squarely into opening slot.  
6. Finished Mounting board will exit through rear of machine.  
7. When you are finished laminating, press the power button to turn machine off.  
'***USEFUL INFORMATION***  
* The document, which has been mounting board laminated, is  
pretty hot and easily bent. Try not to touch the document until  
it has cooled down.  
* When laminating to mounting board, pressure adjustment is  
needed for good quality lamination.  
'***LAMINATION PRESSURE ADJUSTMENT***  
* When you do laminating several colors, use high temperature tape  
to hold color foils in place.  
1. Unplug the machine and unscrew the 8 screws on bottom of laminator,  
set machine upright and lift off the cover.  
2. Locate each end of left and right pressure spring on the upper part as shown.  
3. Reassemble top cover with 8 retaining screws and do lamination.  
* For general lamination, set pressure springs to lower position.  
10  
 
NB-1900N  
CLEANING ROLLERS AND REMOVING FILM JAMMED  
OR STUCK TO ROLLERS  
1. Cleaning rollers with a clean and thick paper  
1) If film adhesive apears on the laminated pouch surface, Insert a sheet of  
clean, thick paper (about 0.5mm(1/50") thickness) into the machine 2~3  
times on "FUNC 4" setting. The paper will attract the excess adhesive  
from the roller.  
2. Cleaning rollers with cleaning solvent.  
1) When rollers are hot, turn on and  
set "COLD" mode to cool them down.  
2) Press the power button to turn off.  
3) Loosen 8 retaining screws on bottom  
and lift off the cover.  
4) Use a recommended silicon roller  
cleaning solvent such as Laminex  
Poly-Off or equivalent, on a lint-free  
cloth to clean residue of laminate  
adhesive on exposed roller surface.  
Prevent any liquid from spilling into  
the unit.  
5) Re-assemble the unit in reverse-order  
of disassembling.  
* Do not turn the unit on until the rollers are completely dry.  
Wet rollers could cause serious harm.  
Be careful not to allow to damage temperature sensor, as damaged  
sensor could cause serious harm.  
11  
 
NB-1900N  
IMPORTANT SAFETY CONCERNS  
1. Be sure that neckties, necklaces, long hair and loose clothing are  
kept away while the laminator is in operation.  
2. Prevent children from accessing the machine.  
3. Place the machine on a sturdy, flat work surface to prevent damage.  
4. Make certain that the machine is connected to an adequate power source.  
5. Do not use for any other purpose, other than laminating.  
MAINTENANCE  
1. Width of upper and lower side of film should be same in order not to  
allow melted adhesive to stick to the roller.  
2. Routine roller cleaning is required to prevent adhesive build-up.  
3. Always keep the machine clean.  
To remove dust, finger prints, etc. on housing, use diluted alcohol on  
lint-free cloth. Prevent any liquids from getting into the laminator.  
(Do not use strong alcohol or petroleum-based cleaning solvents  
or abrasives.)  
ASSEMBLY PARTS  
Owner's manual : 1EA  
TROUBLESHOOTING  
Symptom  
Cause  
Check point  
*Motor doesn't work.  
1.Power cord may not be 1.Check the power cord.  
plugged in  
2.Power switch in  
OFF mod  
2.Check that switch is on  
*Film is not laminated.  
1.Cold mode is set.  
1.Change the setting to  
hot laminatio  
*Lamination  
is not clear.  
1.Setting is too low.  
1.Increase setting.  
12  
 
NB-1900N  
SPECIFICATIONS  
DESCRIPTION  
NB-1900N  
Dimensions(w x d x h)  
680x225x127mm (26.8"x10"x5")  
Max. Laminating Width  
445mm (17.5")  
2mm (1/12")  
Max. Laminating Thickness  
Film Thickness  
75~125(micron)  
Transport Type  
Heat Source  
Four Roller (no carrier)  
Hot roller  
Pre-Heating Time  
4~5 min  
Temp. Operating Range  
8 SETTINGS  
Cooling Fan Type  
Motor Type  
DC FAN  
AC motor  
Max. Laminating Speed  
Weight  
520mm (20.5") per min.  
11Kg (24 lbs.)  
AC 100V 50/60Hz,  
AC 120V 60Hz ,  
AC 220-240V 50/60Hz  
Voltage/Cycle  
Power Consumption  
1000 W  
13  
 
CORPORATE HEADQUARTERS  
Royal Sovereign International Inc.  
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.  
TEL : +1) 800-397-1025  
FAX : +1) 201-750-1022  
E-mail : [email protected]  
RS Holland B.V.  
Royal Sovereign Inc. <Oversea Sales Office>  
1001, World Meridian II, 426-5, Gasan-dong,  
Geumcheon-gu, Seoul, 153-759, KOREA  
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830  
E-mail : [email protected]  
Industrieweg 6K, 4104AR, Culemborg, The Netherlands  
TEL : +31 (0)345 473 097  
FAX : +31 (0)345 519 811  
E-mail : [email protected]  
RS International Australia PTY. LTD.  
30 Prime Drive, Seven Hills, NSW 2147, Australia  
TEL : +61) 2-9674-2127  
RS Canada Inc.  
1025 Westport Crescent, Mississauga On L5T 1E8 CANADA  
TEL : +1) 905-461-1095  
FAX : +61) 2-9674-2027  
E-mail : [email protected]  
FAX : +1) 905-461-1096 TF: +1) 866 961-6673  
E-mail : [email protected]  
 

Radica Games Handheld Game System 75008 User Guide
RCA Clock Radio RP3753 User Guide
RCA Flat Panel Television HD61LPW63 User Guide
RCA Projection Television HD50LPW69 User Guide
Roberts Radio Clock Radio CR9945 User Guide
RocketFish TV Video Accessories RF TVMLPT01 User Guide
Ryobi Trimmer HT920Dr User Guide
Samsung Scanner GH68 06534A User Guide
Sanyo Battery Charger N 550AAS User Guide
Schumacher Battery Charger SC 8000A User Guide