Rosewill Computer Hardware RC214 User Guide

eSATA II 1+1 PCIe Card RC214  
User Manual  
 
eSATAII 1+1 PCIe Card RC214  
User Manual  
2.1. Windows NT 4.0, Windows 2000/Server 2003/XP/VISTA Fresh OS installation  
Follow the instructions in this section if you are performing a new installation of Windows NT 4.0, 2000/XP, Server 2003 and you wish to boot from  
a device attached to the SATA port.  
1. Power off the system. Insert SATA Card into an available PCI slot. Connect serial ATA cable(s) between the SATA port and serial ATA device(s). Power  
up the system.  
2. Put your Windows NT/2000/XP or Windows Server 2003 CD into the CD-ROM/DVD drive, or the NT/2000 boot diskette #1 in the floppy drive if your  
system cannot boot from the CD.  
3. Press F6 for third party SCSI or driver installation at the beginning of text mode installation. Press 'S' when setup asks if you want to specify  
an additional device, and insert the driver CD. Press 'Enter' and select 'Silicon Image SiI 3132 SATALink Controller'.  
4. Press 'Enter' again when prompted to continue on with text mode setup.  
5. Follow the setup instructions to select your choice for partition and file system.  
6. After setup examines your disks, it will copy files from the CD to the hard drive selected above and restart the system. After restart the setup process  
will resume to finish the installation.  
7. Once the operating system installation has completed you can follow the instructions in section 2.4 to verify controller was installed correctly.  
2.2. Adding the HBA to an existing Windows NT Installation  
1. Power off the system. Insert SATA Card into an available PCI slot. Connect serial ATA cable(s) between the SATA port and serial ATA device(s). Power  
up the system.  
2. After OS boots up, Click 'Start'  
3. Under 'Settings', click 'Control Panel'.  
4. Select 'SCSI Adapters' from the Control Panel.  
5. Select the 'Drivers' tab and click 'Add'.  
6. Click 'Have Disk'.  
7. Points specify a location, example E:\SATA Express_2Port \Sil3132 \ WinXP_2000_2003_NT, and click “OPEN” then “OK”  
8. Choose 'Silicon Image SiI 3132 SATALink Controller' and click 'OK'.  
9. After the driver installation has completed you can follow the instructions in section 2.4 to verify controller was installed correctly.  
2.3. Adding the HBA to an existing Windows 2000/Server 2003/XP/VISTA installation  
1. Power off the system. Insert SATA Card into an available PCI slot. Power up the system.  
2. During OS boot up, Windows will display the 'Found New Hardware Wizard'. 'Mass Storage controller'.  
3. Select “Install from a list or specific location (Advanced)”, and click “Next”, and make sure the Driver CD is in your CD-ROM/DVD  
4. Select “Search for the best driver in these locations”, and check Include this location in the search:” uncheck the other boxes.  
5. Type in E:\ (If your CD-ROM/DVD is E:\) then click “Browse”.  
6. Points specify a location, example E:\SATA Express_2Port \Sil3132 \ WinXP_2000_2003_NT, and click “OPEN” then “OK”  
7. When the wizard indicates that it found a driver for the device click 'Next'  
8. If the 'Hardware Installation' dialog appears, click 'Continue Anyway'  
9. The wizard will now copy the required files to the system and start the Driver. After starting the driver the wizard  
will display a completion dialog, click 'Finish' to exit the wizard.  
2.4. Verifying the installation Windows NT, Windows 2000/Server 2003/XP/VISTA installation  
3
 
eSATAII 1+1 PCIe Card RC214  
User Manual  
For Windows NT 4.0  
1. Double click on 'My Computer' icon, select 'Control Panel', click on 'SCSI Adapters' icon, 'Silicon Image SiI 3132 SATALink Controller' should  
displayed correctly under 'Device' and 'Driver' tab.  
2. To view information about the devices attached to the controller, use the SiICfg Utility and click on the device from the list.  
For Windows 2000/XP/VISTA  
1. Right click on 'My Computer' icon, select 'Properties', left click on 'Hardware' tab, and then on 'Device Manager' button.  
2. Double click on 'SCSI and RAID Controllers', If there is no yellow '! ' or ' ? ' in front of 'Silicon Image SiI 3132 SATALink Controller', the driver is  
started correctly.  
3. To view information about the devices attached to the controller, use the SiICfg Utility and click on the device from the list.  
2.5. Update new driver on Windows NT 4.0  
1. After OS boots up, Click 'Start'  
2. Under 'Settings', click 'Control Panel'.  
3. Select 'SCSI Adapters' from the Control Panel.  
4. Select the 'Drivers' tab and click 'Add'.  
5. Click 'Have Disk'.  
6. Insert the Driver CD in your CD-ROM/DVD drive and press 'Enter'.  
7. Choose ' E:\SATA Express_2Port \Sil3132 \ WinXP_2000_2003_NT ' and click 'OK'.  
8. Refer to instructions in section 2.4 to verify controller was installed correctly.  
2.6. Update new driver on Windows 2000/Server 2003/XP/VISTA installation  
1. Right click on 'My Computer' and select 'Properties'. Under the 'System Properties' section, click on 'Hardware' tab, and then on 'Device  
Manager' click 'SCSI and RAID Controllers' and right click 'Silicon Image SiI 3132 SATALink Controller' then select 'Properties' from the context  
menu.  
2. Click 'Driver' ,'Update Driver' and select 'Search for a suitable driver for my device[Recommended]'. Insert the Driver CD in your CD-ROM/DVD  
drive. Click 'Next' and complete the driver installation.  
3. System will go through the enumeration process and install the driver. At the end of the process, click 'Yes' to reboot your system when  
necessary.  
4. See instructions in section 2.4 to verify controller was installed correctly.  
Thank you for purchasing a quality Rosewill Product.  
4
 

QUAD Stereo Amplifier Vaccume Tube Amplifier Systems User Guide
Radio Shack Telephone ET 3204 User Guide
RCA Speaker System RTD206 User Guide
Ricoh Fax Machine 3245 User Guide
RIDGID Freezer R5013 User Guide
Samsung Dishwasher DW7933LRABB User Guide
Samsung Printer CLX 3160 User Guide
Sansui Flat Panel Television SLED2237 User Guide
Sanyo DVR DSR M User Guide
Sanyo Flat Panel Television DP26648 User Guide