Rheem Water Heater RH DV50FV User Guide

Rheemglas® Energy Miser® Direct Vent Gas Water Heaters  
now with the Guardian System™  
Fury DV  
LONGER VENTING AVAILABLE  
Available in 50 Gallon Gas Model  
6-Year Limited Tank Warranty, 1-Year Limited Parts Warranty*  
NEW FVIR Compliant!  
Adjustable coaxial vent allows flexibility  
of installation – uses outside air for combustion  
and requires no electrical power  
Aluminum vent and cap base to prevent  
staining of building exterior  
Anode rod equalizes aggressive water action  
High temperature silicone bands reduce venting  
installation time  
Internal air tube for reduced footprint  
Meets ANSI Z21.10.1 requirements for  
Flammable Vapor Ignition Resistance (FVIR)  
Meets or exceeds National Appliance Energy  
Conservation Act (NAECA) requirements  
Brass drain valve  
Factory installed temperature and pressure  
relief valve  
R-Foam® insulation for superior heat retention  
Exclusive Rheemglas® tank lining resists  
corrosion and prolongs tank life  
* See Residential Warranty Information Brochure for complete  
warranty information.  
Energy Factor based on D.O.E. (Department of Energy) test procedures.  
Heat saving flue baffle design  
Gas control and combination thermostat  
®
DESCRIPTION  
FEATURES  
RECOVERY IN  
DIMENSIONS  
ENERGY INFO.  
GAS INPUT IN  
FIRST HOUR  
DEL. G.P.H.  
NAT.  
HT. TO  
VENT  
A
TANK  
HT.  
B
HT. TO  
VENT  
SIZE  
E
HT. TO  
SIDE T&P  
F
SHIP.  
WT.  
(LBS)  
ENERGY  
FACTOR  
NAT.  
GALLON  
MODEL  
THOUS. BTU/HR. G.P.H. 90° RISE  
DIAMETER GAS CONN.  
CAPACITY NUMBER  
C
D
NAT.  
NAT.  
50  
RH DV50FV  
38  
38.4  
80  
68  
59-1/2 21-3/4  
14-1/4  
6
52-1/2  
165  
0.58  
ANODE  
SIDE VENTING (G)  
WITH INCLUDED  
VENT KIT  
SIDE VENTING (G)  
WITH OPTIONAL  
VENT KIT  
VENTING – ROUGHING IN DIMENSIONS (INCHES)  
COLD WATER  
CONNECTION  
MODEL  
4 FEET VENTING  
AVAILABLE  
OPTIONAL HEIGHT (A)  
WITH VENT KIT  
NUMBER  
MIN.  
MAX.  
MIN.  
MAX.  
HOT WATER  
CONNECTION  
& Vertical  
RH DV50FV  
Horizontal  
8-1/8  
18-1/8  
8-1/8  
48**  
68 – 107†  
** Horizontal Vent Kit #SP20131. Venting dimensions are approximate.  
† Vertical Vent Kit #SP20132. Venting dimensions are approximate.  
• If side wall is combustible material, 1" clearance must be included in adjustment range.  
10"  
E
G
These units are designed  
to meet or exceed ANSI  
(American National  
NEW LONGER VENTING!  
• Up to 4 feet above the water heater  
and 4 feet from an outside wall.  
(G: SIDE VENTING  
Standards Institute)  
RANGE OF  
ADJUSTMENT)  
requirements and have been  
tested according to D.O.E.  
test procedures and meet or  
exceed the energy efficiency  
requirements of NAECA,  
ASHRAE standard 90, ICC  
Code and all state energy  
efficiency performance  
criteria for energy consuming  
appliances.  
Order Horizontal Vent Kit:  
#SP20131  
3/4" N.P.T.  
RELIEF VALVE  
OPENING  
Order Vertical Vent Kit:  
#SP20132  
C
Rheem Exclusive Adjustable  
Coaxial Vent Allows Flexibility  
of Installation…  
You may orient the Fury DV  
for easiest service  
access, because the  
adjustable coaxial  
vent can swivel  
A
B
F
1/2"  
Before purchasing this  
appliance, read important  
energy cost and efficiency  
information available from  
your supplier.  
D
EXTERIOR  
WALL  
360 degrees.  
In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.  
Rheem Manufacturing Company • Water Heater Division  
Rheem Canada Ltd./Ltée, 128 Barton Street West, Hamilton, Ontario L8N 3P3  
12/07 WP  
FORM NO. 101-22EFCAN Rev1  
 

Pyramid Technologies Speaker PW1086 X User Guide
QSC Audio Stereo Amplifier USA 1310 User Guide
Radio Shack Washer 49 1010 User Guide
Renesas Network Card M3T FLX 144NSE User Guide
Roland Musical Instrument VS 1680 User Guide
Ryobi Portable Generator RYI2000T User Guide
Samsung Bluetooth Headset GH68 18475A User Guide
Samsung Stereo System AH68 01018B User Guide
Savin All in One Printer 2335 User Guide
SECO LARM USA Home Security System VA 1102B WQ User Guide