Radio Shack Two Way Radio TRC 239 User Guide

21-1628.fm Page 1 Tuesday, January 25, 2000 9:30 AM  
Cat. No. 21-1628  
OWNER’S MANUAL  
Please read before using this equipment.  
TRC-239  
40-Channel, 4-Watt  
CB Walkie-Talkie  
 
21-1628.fm Page 3 Tuesday, January 25, 2000 9:30 AM  
Rotary Volume and Squelch Controls  
— mean  
faster, easier operation under virtually any condition.  
Automatic Modulation Limiter  
— prevents over-  
modulation to ensure a clear sound.  
Automatic Noise Limiter  
— reduces noise caused  
by nearby electrical equipment such as motors or au-  
tomotive ignition systems.  
CHARGE Indicator  
— lights to indicate that the  
TRC-239 is charging your optional rechargeable bat-  
teries.  
3
 
21-1628.fm Page 4 Tuesday, January 25, 2000 9:30 AM  
FCC INFORMATION  
The Federal Communications Commission (FCC)  
does not require you to have a license to operate this  
CB. However, the FCC does require that you read  
and know Part 95 of FCC Rules. These rules apply to  
the operation of a Class D CB. We have provided a  
copy of these regulations with your CB.  
Warning:  
Do not open your CB to make any internal  
adjustments. Any internal adjustments can be made  
only by an authorized service technician.  
Unauthorized internal adjustments and/or modifica-  
tions can lead to illegal operation as defined by Part  
95 of FCC Rules. Such illegal operation can lead to  
very serious consequences. To be safe and sure:  
• Never open your CB’s case.  
• Never modify your CB.  
Your CB might cause TV or radio interference even  
when it is operating properly. To determine whether  
your CB is causing the interference, turn off your CB.  
If the interference goes away, your CB is causing it.  
Try to eliminate the interference by either moving  
your CB away from the receiver or contacting your lo-  
cal RadioShack store for help. If you cannot elimi-  
nate the interference, the FCC requires that you stop  
using your CB.  
4
 
21-1628.fm Page 5 Tuesday, January 25, 2000 9:30 AM  
CONTENTS  
Preparation ........................................................... 6  
Powering the CB ............................................. 6  
Using the POWER Jack and  
NI/AL Switch ............................................ 6  
Using Batteries ............................................... 7  
Using Non-Rechargeable Batteries ......... 7  
Using Rechargeable Batteries ................. 8  
Charging Tips .......................................... 9  
Using Vehicle Battery Power ........................ 10  
Using AC Power ............................................ 11  
Connecting the Antenna ............................... 12  
Connecting an Optional Antenna .......... 13  
Operation ............................................................ 15  
Receiving Transmissions and  
Adjusting Squelch ......................................... 15  
Transmitting .................................................. 15  
CB Operation Tips ............................................. 17  
Typical Uses For a CB Radio ....................... 17  
Business Uses ...................................... 17  
Personal Uses ....................................... 17  
CB Courtesy .......................................... 18  
Using Common 10-Codes ................................. 19  
Maximum Range .......................................... 21  
Care and Maintenance ....................................... 22  
Specifications .................................................... 23  
5
 
21-1628.fm Page 6 Tuesday, January 25, 2000 9:30 AM  
PREPARATION  
POWERING THE CB  
You can power your TRC-239 from any of these  
sources:  
• internal batteries (not supplied)  
• vehicle battery power (using an optional  
adapter)  
• household AC power (using an optional adapter)  
Using the POWER Jack and NI/AL  
Switch  
POWER  
The  
jack lets you connect an external power  
source (such as your vehicle’s battery) or an external  
AC adapter (not supplied), or an external charger  
(not supplied) to charge rechargeable batteries (not  
supplied) while they are in the TRC-239. Before con-  
POWER  
NI/AL  
cor-  
necting anything to  
rectly.  
, you must set  
NI/AL  
Follow these steps to set  
.
1. Slide the battery compartment cover in the direc-  
tion of the arrow to remove it.  
2. Remove any installed batteries.  
NI/AL  
3. Set  
as follows:  
AL  
• Set it to  
to use alkaline batteries.  
6
 
21-1628.fm Page 7 Tuesday, January 25, 2000 9:30 AM  
NI/AL  
NI  
to use rechargeable batteries  
• Set  
to  
inside the TRC-239  
Warning:  
To avoid injuring yourself or damaging the  
POWER  
TRC-239, connect a battery charger to  
when using Ni-Cd or Ni-MH batteries.  
only  
USING BATTERIES  
Your TRC-239 can use 9 AA batteries (not supplied)  
for power. For the best performance and longest life,  
we recommend RadioShack non-rechargeable alka-  
line or rechargeable nickel-cadmium/nickel-metal hy-  
dride batteries.  
Cautions:  
• Use only fresh batteries of the required size and  
recommended type.  
• Do not mix old and new batteries, different types  
of batteries (standard, alkaline, or recharge-  
able), or rechargeable batteries of different  
capacities or type.  
Using Non-Rechargeable Batteries  
Follow these steps to install non-rechargeable batter-  
ies.  
1. Slide the battery compartment cover in the direc-  
tion of the arrow to remove it.  
2. Place the batteries in the compartment as indi-  
cated by the polarity symbols (+ and –) marked  
inside.  
3. Replace the cover.  
7
 
21-1628.fm Page 8 Tuesday, January 25, 2000 9:30 AM  
When the TX/BATT indicator lights steadily or the  
TRC-239 stops operating properly, replace the bat-  
teries.  
Warning:  
Dispose of old batteries promptly and  
properly. Do not burn or bury them.  
Caution:  
If you do not plan to use the TRC-239 with  
internal batteries for several months, remove the bat-  
teries. Batteries can leak chemicals that can destroy  
electronic parts.  
Using Rechargeable Batteries  
Rechargeable batteries come fully discharged. Be-  
fore you use them for the first time, you must charge  
them. You can charge the batteries while they are in  
the battery compartment using a battery charger,  
such as RadioShack Cat. No. 23-349 (not supplied).  
Or you can use an optional external battery charger  
(not supplied).  
Warning:  
Do not try to charge non-rechargeable bat-  
teries. They might get very hot and they could ex-  
plode.  
Follow these steps to charge nickel-cadmium or  
nickel-metal hydride batteries in the TRC-239’s bat-  
tery compartment.  
VOLUME  
1. Rotate  
upward until it clicks.  
2. Set the battery charger’s Ni-Cd/Ni-MH selector  
switch to the appropriate position.  
3. Insert the charger's barrel plug into the TRC-  
POWER  
239’s  
jack.  
8
 
21-1628.fm Page 9 Tuesday, January 25, 2000 9:30 AM  
4. Plug the charger's other end into a standard AC  
outlet.  
It takes 14–16 hours to recharge Ni-MH batter-  
ies or 7–8 hours to recharge Ni-Cd batteries that  
are fully discharged.  
5. When the batteries are fully charged, unplug the  
charger from the AC outlet, then disconnect the  
charger from the CB.  
Charging Tips  
• Fully discharge Ni-Cd batteries occasionally by  
using the TRC-239 until the TX/BATT indicator  
lights, then fully recharge the batteries. This  
helps restore and maintain the ability of the bat-  
teries to take a maximum charge. (This does not  
apply to Ni-MH batteries.)  
To prevent damage to rechargeable batteries,  
never charge them in an area where the temper-  
ature is above 122°F (50°C) or below 32°F  
(0°C).  
• Do not overcharge batteries. Overcharging can  
severely reduce the batteries’ useful life.  
• Always disconnect the charger's AC plug before  
you disconnect the barrel plug.  
Important:  
This CB can use nickel-  
cadmium rechargeable batteries. At  
the end of a nickel-cadmium bat-  
tery's useful life, it must be recycled  
or disposed of properly. Contact  
your local, county, or state hazard-  
ous waste management authorities  
0
0
8
3
4
for information on recycling or disposal programs in  
your area or call 1-800-843-7422. Some options that  
9
 
21-1628.fm Page 10 Tuesday, January 25, 2000 9:30 AM  
might be available are: municipal curbside collection,  
drop-off boxes at retailers such as your local Ra-  
dioShack store, recycling collection centers, and  
mail-back programs.  
USING VEHICLE BATTERY  
POWER  
You can power the TRC-239 from a vehicle’s 12V  
power source (such as cigarette-lighter socket) using  
a fused DC power cord that ends in a size M Adapta-  
plug® adapter (neither supplied). Both are available  
at your local RadioShack store.  
Cautions:  
You must use a power source that  
supplies 13.8 volts (12-volt nominal) at  
1300 mA. Its center tip must be set to  
positive and its plug must fit the TRC-239's  
!
POWER  
jack. Using a power source that does  
not meet these specifications could damage the  
TRC-239 or the power cord.  
• Always connect the fused power cord to the  
TRC-239 before you connect it to the power  
source. When you finish, disconnect the fused  
power cord from the power source before you  
disconnect it from the TRC-239.  
NI/AL  
If batteries are installed, make sure  
inside the  
battery compartment is set to the correct position  
(see “Using Batteries” on Page 7).  
10  
 
21-1628.fm Page 11 Tuesday, January 25, 2000 9:30 AM  
Follow these steps to connect the TRC-239 to your  
vehicle’s battery power.  
/
VOLUME  
S
H
M
IC  
V
.8  
3
1
A
E
C
D
G
R
H
C
CITIZENS BAND TRANSCEIVER  
I
H
R
W
P
O
L
1. Plug the power cord’s Adaptaplug into the TRC-  
POWER  
239’s  
jack.  
2. Connect the other end of the power cord to your  
vehicle’s cigarette lighter socket.  
USING AC POWER  
You can power the TRC-239 using an optional DC  
power supply that provides 13.8 volts (12-volt nomi-  
nal) at 1300 mA. You also need a fused power cord  
that ends in a size M Adaptaplug adapter (neither  
supplied). Both are available at your local Ra-  
dioShack store.  
Cautions:  
You must use a power supply that sup-  
plies 13.8V DC and delivers at least  
1300 mA. Its fused connecting cord’s  
center tip must be set to positive and its plug  
!
POWER  
must fit the TRC-239's  
jack. Using a  
power supply that does not meet these specifi-  
cations could damage the TRC-239, the power  
cord, or the power supply.  
• Always connect the power supply to the TRC-  
239 before you connect it to AC power. When  
11  
 
21-1628.fm Page 12 Tuesday, January 25, 2000 9:30 AM  
you finish, disconnect the power supply from AC  
power before you disconnect the power cord  
from the TRC-239.  
If batteries are installed for portable use, make sure  
NI/AL  
inside the battery compartment is set to the  
correct position (see “Using Batteries” on Page 7).  
Follow these steps to connect the TRC-239 to AC  
power.  
1. Connect the Adaptaplug adapter to the power  
supply’s cord, setting TIP to + (positive).  
POWER  
2. Plug the barrel plug into the TRC-239's  
jack.  
3. Connect the other end of the power cord to your  
vehicle’s cigarette-lighter socket.  
4. Plug the power supply into a standard AC outlet,  
then turn on the power supply before you turn on  
the TRC-239.  
CONNECTING THE ANTENNA  
Caution  
: To prevent damage to your TRC-239, you  
must connect an antenna before you operate it.  
Follow these steps to attach the supplied flexible an-  
tenna to your TRC-239.  
12  
 
21-1628.fm Page 13 Tuesday, January 25, 2000 9:30 AM  
1. Align the slots around the antenna’s connector  
with the tabs on the antenna jack on top of the  
TRC-239.  
2. Press the antenna down over the jack and turn  
the antenna’s base clockwise until it locks.  
To remove the antenna, turn the antenna’s base  
counterclockwise until it unlocks, then lift it off the an-  
tenna jack.  
Connecting an Optional Antenna  
The TRC-239 comes with  
a
flexible antenna  
(equipped with a BNC connector) that is ideal for  
most applications. However, the BNC connector  
makes it easy to connect other types of antennas,  
too. For mobile or base station use, you might want  
to connect an optional external antenna. Your local  
RadioShack store carries a wide selection of external  
mobile or outdoor base station antennas. Choose the  
one that best meets your needs.  
When deciding on a mobile or base station antenna  
and its location, consider the following:  
• The location of the antenna should be as high as  
possible.  
• The antenna and antenna cable should be as far  
as possible from sources of electrical noise  
(appliances, other radios, and so on).  
• The antenna should be vertical for the best per-  
formance.  
13  
 
21-1628.fm Page 14 Tuesday, January 25, 2000 9:30 AM  
Note  
: When connecting an optional antenna, always  
use 50-ohm coaxial cable such as RG-58. For  
lengths over 50 feet, use low-loss RG-8 coaxial ca-  
ble. When the cable terminates in a PL-259 connec-  
tor, obtain an adapter to fit the BNC connector.  
Follow the installation instructions supplied with the  
antenna, route the antenna cable to the TRC-239,  
then connect it to the antenna jack.  
Cautions  
:
• Do not run the cable over sharp edges or mov-  
ing parts.  
• Do not run the cable next to power cables or  
other CB antenna cables.  
• Do not run the cable through a vehicle’s engine  
compartment or other areas that produce  
extreme heat.  
• Follow all cautions and warnings included with  
the antenna.  
Warning:  
When installing or removing a base station  
CB antenna, use extreme caution. If the antenna  
starts to fall, let it go! It could contact overhead power  
lines. If the antenna touches the power line, contact  
with the antenna, mast, cable, or guy wires can  
cause electrocution and death! Call the power com-  
pany to remove the antenna. DO NOT attempt to do  
so yourself.  
14  
 
21-1628.fm Page 15 Tuesday, January 25, 2000 9:30 AM  
OPERATION  
Before you start using your TRC-239, we recom-  
mend you read “CB Operation Tips” on Page 17,  
which contains information to help you use the TRC-  
239 effectively and courteously.  
RECEIVING TRANSMISSIONS  
AND ADJUSTING SQUELCH  
Caution:  
Before receiving or transmitting, always  
connect the antenna.  
SQUELCH  
VOLUME  
1. Rotate  
2. Rotate  
fully towards the top of the CB.  
toward the bottom of the CB  
until it clicks. The CB turns on and a channel  
appears. Increase the volume to a comfortable  
listening level. (You might hear a hiss if there is  
no signal on the selected channel.)  
CH  
3. Press  
appears on the display. To move rapidly through  
the channels, hold down or  
or  
until the desired channel  
9
8
.
9
8
SQUELCH  
4. Rotate  
toward the bottom of the TRC-  
239 until any hiss just stops. This lets you hear  
transmissions without background noise. Rotat-  
ing the control further decreases the TRC-239’s  
sensitivity to incoming signals.  
VOLUME  
5. To turn off the TRC-239, rotate  
until it clicks.  
upward  
TRANSMITTING  
1. Follow Steps 1–4 in “Receiving Transmissions  
and Adjusting Squelch.”  
15  
 
21-1628.fm Page 16 Tuesday, January 25, 2000 9:30 AM  
2. Based on your desired transmitting range, set  
the power level as follows.  
To increase the transmitted signal strength  
PWR HI/LO  
and the TRC-239's range, set  
to  
HI  
.
To decrease the transmitted signal strength  
(to prevent overloading a nearby CB) and  
PWR HI/LO  
LO  
.
save battery power, set  
to  
3. Hold the CB 2 to 3 inches from your mouth. Hold  
PTT  
down  
(push to talk) and speak into the  
microphone on the front of the CB in a normal  
voice. TX/BATT lights.  
PTT  
4. When you finish speaking, release  
Important!  
.
Channels 9 and 19 are reserved for  
motorist assistance and for reporting emergency  
information about accidents, hazardous road  
conditions, and so on. Always give emergency  
communications priority on Channels 9 and 19.  
VOLUME  
5. To turn off the TRC-239, rotate  
until it clicks.  
upward  
16  
 
21-1628.fm Page 17 Tuesday, January 25, 2000 9:30 AM  
CB OPERATION TIPS  
Like most activities, CB radio users have customs  
and courtesies. The following tips will help you get  
the most enjoyment out of your CB.  
TYPICAL USES FOR A CB RADIO  
Business Uses  
• Truck drivers and delivery personnel can learn  
road and traffic conditions and get assistance in  
locating destinations. A CB is also good com-  
pany on these “long hauls.”  
• Used by construction crews, a CB quickly pays  
for itself when you are calling for additional  
materials or coordinating the activities of differ-  
ent work crews.  
• For security officers, a CB is more than a conve-  
nience — it is a must for both safety and effi-  
ciency.  
Personal Uses  
• Keep in touch with home while driving to work, to  
the store, or to a social activity. Let your family  
know you are tied up in traffic or that you will  
stop by the store on the way home.  
• If you are a two-or-more car family, CBs are  
great for inter-car communications while family  
members are going places.  
• Contact friends or neighbors — find out “what's  
happening” or plan a get-together.  
17  
 
21-1628.fm Page 18 Tuesday, January 25, 2000 9:30 AM  
• Ever have car trouble or run out of gas on the  
highway? With your CB you can have peace of  
mind knowing you can call for assistance.  
• Camping, fishing, and other sports are more fun  
with a CB. Keep in touch with a buddy or find out  
“what's cooking” back at camp.  
CB Courtesy  
• Wait for a pause in someone else's transmission  
before you ask for a break.  
• If you do not receive an answer to your call after  
a second attempt, sign off and wait several min-  
utes before trying again.  
PTT  
• Do not hold down  
, called “dead keying”,  
when you are not talking.  
• Assist callers with directions, information about  
road conditions, and any other reasonable  
requests.  
18  
 
21-1628.fm Page 19 Tuesday, January 25, 2000 9:30 AM  
USING COMMON 10-CODES  
Citizen’s Band operators have largely adopted the  
10-codes for standard questions and answers.  
These codes permit faster communication and better  
intelligibility in noisy areas. While not all codes are  
.
listed, most of the more popular ones follow  
Code  
Meaning  
10-1  
10-2  
10-3  
10-4  
10-5  
10-6  
10-7  
10-8  
10-9  
10-10  
Receiving poorly.  
Receiving well.  
Stop transmitting.  
OK, message received.  
Relay message.  
Busy, please stand by.  
Out of service.  
In service  
Repeat message.  
Transmission com-  
pleted, standing by.  
10-11  
10-12  
10-13  
Talking to rapidly.  
Visitors present.  
Advise Weather/Road  
conditions.  
10-17  
10-18  
10-19  
Urgent business.  
Anything for us?  
Nothing for you. Return  
to base.  
10-20  
10-21  
10-22  
My location is____.  
Call by telephone.  
Report in person  
to____.  
19  
 
21-1628.fm Page 20 Tuesday, January 25, 2000 9:30 AM  
Code  
Meaning  
10-23  
10-25  
10-26  
Please stand by.  
Can you contact____.  
Disregard last informa-  
tion.  
10-27  
I am moving to  
channel____.  
10-28  
10-32  
Identify your station.  
I will give you a radio  
check.  
10-33  
10-36  
10-37  
Emergency traffic.  
Correct time is____.  
Wrecker needed  
at____.  
10-38  
10-41  
10-42  
Ambulance needed  
at______  
Please turn to  
channel_____.  
Traffic accident  
at_____.  
10-43  
10-50  
10-62  
Traffic tie-up at____.  
Break channel.  
Unable to copy; use  
telephone.  
10-70  
Fire at_____.  
Note:  
Although this table lists the 10-codes’ mean-  
ings in the form of a statement, they can also be  
phrased as questions (10-6: Are you busy?, 10-20:  
What is your location?).  
20  
 
21-1628.fm Page 21 Tuesday, January 25, 2000 9:30 AM  
MAXIMUM RANGE  
The maximum range and quality of CB transmissions  
vary depending on the following typical conditions:  
• the type and quality of antenna used  
• the height of the antenna's mounting location —  
the higher the antenna, the greater the signal's  
range  
• the surrounding terrain — mountains and tall  
buildings limit the range  
• weather conditions  
• the number of nearby CBs operating on the  
same channel  
21  
 
21-1628.fm Page 22 Tuesday, January 25, 2000 9:30 AM  
CARE AND MAINTENANCE  
Your RadioShack TRC-239, 40-Channel, 4-Watt,  
CB Walkie-Talkie is an example of superior design  
and craftsmanship. The following suggestions will  
help you care for your CB so you can enjoy it for  
years.  
Keep the CB dry. If it gets wet, wipe  
it dry immediately. Liquids might con-  
tain minerals that can corrode the  
electronic circuits.  
Keep the CB away from dust and  
dirt, which can cause premature  
wear of parts.  
Handle the CB gently and carefully.  
Dropping it can damage circuit  
boards and cases and can cause the  
CB to work improperly.  
Use only fresh batteries of the re-  
quired size and recommended type.  
Batteries can leak chemicals that  
damage your CB’s electronic parts.  
Wipe the CB with a damp cloth occa-  
sionally to keep it looking new. Do  
not use harsh chemicals, cleaning  
solvents, or strong detergents to  
clean the CB.  
Modifying or tampering with the CB’s internal com-  
ponents can cause a malfunction and might invali-  
date its warranty and void your FCC authorization  
to operate it. If your CB is not performing as it  
should, take it to your local RadioShack store for  
assistance.  
22  
 
21-1628.fm Page 23 Tuesday, January 25, 2000 9:30 AM  
SPECIFICATIONS  
RECEIVER  
Frequency Coverage ............. 26.965 to 27.405 MHz  
Audio Output ............................ 400 mW (10% THD)  
Intermediate Frequency ............. 1st IF: 10.695 MHz  
2nd IF: 455 kHz  
TRANSMITTER  
Frequency Coverage ............. 26.965 to 27.405 MHz  
Output Power ................. 4 Watts (HI), 1 Watt (LOW)  
Antenna Impedance .................................... 50 Ohm  
Current Drain:  
with 80% modulation ................... 700/1300 mA  
without modulation ......................... 500/850 mA  
GENERAL  
Power Requirements ........ 12V DC or 9 AA batteries  
Operating Temperature Range ................ 0° to 140°F  
(–18° to 60°C)  
Size and Type of Batteries:  
AA Alkaline, Ni-Cd, or Ni-MH  
Number of Batteries ............................................... 9  
DC Input Jack ................Type M Adaptaplug adapter  
with tip positive  
Specifications are typical; individual units might vary.  
Specifications are subject to change and improve-  
ment without notice.  
23  
 
21-1628.fm Page 24 Tuesday, January 25, 2000 9:30 AM  
Limited Ninety-Day Warranty  
This product is warranted by RadioShack against manufacturing  
defects in material and workmanship under normal use for ninety  
(90) days from the date of purchase from RadioShack company-  
owned stores and authorized RadioShack franchisees and deal-  
ers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO  
EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,  
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION  
TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES  
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO  
CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-  
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DI-  
RECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF  
THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS  
WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAM-  
AGES RESULTING FROM INCONVENIENCE, LOSS OF TIME,  
DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,  
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,  
EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBIL-  
ITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied war-  
ranty lasts or the exclusion or limitation of incidental or conse-  
quential damages, so the above limitations or exclusions may not  
apply to you.  
In the event of a product defect during the warranty period, take  
the product and the RadioShack sales receipt as proof of pur-  
chase date to any RadioShack store. RadioShack will, at its op-  
tion, unless otherwise provided by law: (a) correct the defect by  
product repair without charge for parts and labor; (b) replace the  
product with one of the same or similar design; or (c) refund the  
purchase price. All replaced parts and products, and products on  
which a refund is made, become the property of RadioShack.  
New or reconditioned parts and products may be used in the per-  
formance of warranty service. Repaired or replaced parts and  
products are warranted for the remainder of the original warranty  
period. You will be charged for repair or replacement of the prod-  
uct made after the expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or  
attributable to acts of God, abuse, accident, misuse, improper or  
abnormal usage, failure to follow instructions, improper installa-  
tion or maintenance, alteration, lightning or other incidence of ex-  
cess voltage or current; (b) any repairs other than those provided  
by a RadioShack Authorized Service Facility; (c) consumables  
such as fuses or batteries; (d) cosmetic damage; (e) transporta-  
tion, shipping or insurance costs; or (f) costs of product removal,  
installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also  
have other rights which vary from state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor,  
Fort Worth, TX 76102  
12/99  
We Service What We Sell  
937568  
01A00  
Printed in Thailand  
 

QSC Audio Stereo Amplifier DCA Series User Guide
RCA Microwave Oven RMW743 User Guide
RCA Universal Remote RCR313BR User Guide
Samsung Digital Camera EC ES70ZZBPBPA User Guide
Samsung Telephone DCS 816 User Guide
Sanyo Battery Charger UF653450R User Guide
Sanyo Camera Accessories UR 521 User Guide
Seagate Computer Drive EE252 User Guide
Sears Lawn Mower 247370291 User Guide
Sears Treadmill 24959 User Guide