RCA Universal Remote RCR 3283 User Guide

RCR3283 / RCR3383  
Universal Remote Control  
Owner’s Manual  
Manual del Propietario (parte posterior)  
Three-component  
Universal Remote  
Component  
keys (TV,  
INFO key  
displays  
Congratulations on your purchase of this three-component  
universal remote. This universal remote controls up to three  
electronic components and makes juggling remote controls a  
thing of the past. Your remote is guaranteed to work with all  
brands of components. The three-component universal remote  
is easy to use, easy to program and gives you control at the  
touch of your fingertips.  
SAT•CBL,  
DVD•VCR)  
information  
for the  
component  
you’re  
controlling  
Dedicated  
MENU and  
GUIDE  
keys let  
SAVE THIS MANUAL AND THE CODE LISTS!  
Transport  
keys,  
you access  
advanced  
component  
functions  
Remote controls can sometimes lose their programming when you  
change the batteries. Make sure you keep the manual and code lists in  
a safe place so that you can reprogram the remote if you need to.  
including  
SKIP and  
SLOW, give  
you better  
DVD/DVR  
control  
Tip: The three-component universal remote is already programmed to  
operate most RCA, GE and PROSCAN branded TVs, VCRs, DVD  
players and satellite receivers. Just press the corresponding key—DVD•VCR  
for a DVD player, TV for a television, SAT•CBL for a satellite receiver.  
Arrow  
keys for  
navigating  
your  
components’  
menu  
Battery Installation and Information  
Your universal remote requires two AAA Alkaline batteries  
(batteries may or may not be included, depending on model).  
To install the batteries:  
systems  
1. Press and push the battery  
compartment cover to remove it..  
2. Insert the batteries, matching the  
batteries to the (+) and (–) marks  
inside the battery compartment.  
3. Push the battery cover back into  
place.  
Actual  
model may  
vary from  
picture  
Note: If you are replacing batteries, try not to press any buttons after  
you’ve taken the old batteries out. Pressing buttons while replacing  
batteries causes the remote to lose the devices you’ve programmed. You  
will need to program the remote again.  
shown  
Battery Precautions:  
• Do not mix old and new batteries.  
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-  
cadmium) batteries.  
• Always remove old, weak or worn-out batteries promptly and recycle or  
dispose of them in accordance with Local and National Regulations.  
The INPUT and — (dash) key has three functions: (ꢀ)  
it toggles through all the video sources connected  
to your TV; (2) when the remote is in VCR mode,  
this button toggles between VCR and the TV input;  
(3) when you’re entering digital channel numbers  
directly, this button lets you separate the main  
channel number from the subchannel number  
Battery Saver  
Your universal remote control saves battery power by  
automatically turning off if any key is pressed for more than  
60 seconds. This saves your battery life should your remote  
get stuck in a place where the keys remain depressed, such as  
between sofa cushions.  
Programming Your Remote  
Care and Maintenance  
• Keep the remote dry. If it gets wet, wipe it dry immediately.  
Your universal remote can operate a variety of brands of  
components. In order for your universal remote to control your  
components, you need to program the remote with the codes  
that match the components (See Code Lists enclosed or go to  
rca.com/codefinder). These codes enable the remote to  
communicate with your components. Each brand and each  
component has its own “language,” and, by programming the  
correct codes into your remote, you tell the remote to “speak the  
same language” as your components.  
• Use and store the remote only in normal temperature  
environments.  
• Handle the remote gently and carefully. Don’t drop it.  
• Keep the remote away from dust and dirt.  
• Wipe the remote with a damp cloth occasionally to keep it  
looking new.  
• Modifying or tampering with the remote’s internal components  
can cause malfunction and invalidate its warranty.  
 
Direct Code Entry  
To use the direct code entry method to program your universal  
remote to control your components, follow the steps below.  
Manual Code Search and Entry  
If your component’s brand isn’t listed in the Code Lists, or if  
you have tried all of the codes for your brand and the remote  
does not operate your component, try one of the Code Search  
methods below—Manual Code Search or Auto Code Search.  
Both Code Search methods cycle through all of the codes in  
the Code Lists in the event that your component’s code is  
listed under another brand.  
1. Manually turn on the component you want the remote to  
control (TV, VCR, DVD, DVR, satellite receiver, or cable box).  
2. Locate the enclosed Code Lists. Find the list for the  
component you wish to program. Find your component’s  
brand. You will see a listing of four-digit codes for each  
brand. If your brand isn’t listed, use one of the Code Search  
methods to program the remote control. (Refer to pages 3–5  
for Manual and Auto Code Search methods.)  
Note: The Manual Code Search method may take a long time  
because the remote searches through all of the codes in its memory for  
the code that operates your component. Therefore, if your brand is  
listed in the Brand Codes or the Code Lists, first try the Brand Code  
Search or the Direct Code Entry method described on pages 2–3.  
Note: You can also use the online code finder at  
TIP: To exit without saving at any point in the Manual  
Code Search, press and release the CLEAR key.  
LED  
3. Press and hold the component key  
(TV, SAT•CBL, DVD•VCR) you  
wish to program. The LED turns  
on and remains on.  
1. Manually turn on the component you want the remote to  
control (TV, VCR, DVD, DVR, satellite receiver, or cable box).  
Keep holding down the  
Note: To program the DVD•VCR key to control a VCR or DVR,  
component key. If you release the  
component key any time during  
the Direct Code Entry procedure, the LED blinks four times,  
and the process is exited. The last programmed code under  
the component key is retained.  
see below.  
LED  
2. Press and hold the component key  
(TV, SAT•CBL, DVD•VCR) you  
wish to program. The LED turns  
on and remains on. Keep holding  
down the component key.  
Notes: To program the DVD•VCR key to control a VCR or DVR,  
3. While holding the component key  
down, press and hold the POWER  
see below.  
4. While holding down the component key, consult the  
Code Lists for the four-digit code that corresponds to your  
component’s brand and use the number keys (0-9) to enter  
it. After you press the first number, the LED turns off. After  
the fourth number is entered, the LED turns on.  
key. The LED turns off. After holding down both keys for  
three seconds, the LED turns back on.  
4. Release both keys. The LED remains on.  
Note: If you press an invalid key during Manual Code Search, the  
remote does not respond and the search times out after two minutes.  
When the search times out, the LED blinks four times and turns off.  
The last programmed code under that component key is retained.  
TIP: Throughout the programming of each key, be sure to keep the  
remote pointed at the IR sensor of the component you are currently  
programming the remote to control.  
TIP: Throughout the programming of each key, be sure to keep the  
remote pointed at the IR sensor of the component you are currently  
programming the remote to control.  
5. Release the component key. If the LED turns off, you  
have entered a valid code and have followed the correct  
procedure for Direct Code Entry. Proceed to the next step.  
If the LED blinks four times, you have either entered a code  
number that is not in the code lists or missed a step in the  
code entry procedure. Repeat the Direct Code Entry process  
from step 3 and try the next code listed.  
5. Press and release the POWER key repeatedly until your  
component turns off. Each time you press the POWER key,  
the LED blinks, and the next code in the list is sent. This  
process continues until all of the codes in the Code Lists  
have been tried. If your component turns off, you have  
found the correct code. (If it cycles through and the LED  
blinks four times and turns off, all codes have been searched.  
The Manual Code Search method is exited.)  
6. To confirm that the component key is programmed with the  
correct code for maximum functionality, test the component.  
Attempt to control a variety of the component’s functions  
with the remote. If some features of your components do not  
work, try programming the remote with a different code in the  
list until you find the code that allows the remote to control  
the majority of your component’s functions. Different codes  
can provide different levels of functionality.  
TIP: Because there are so many codes, you may have to press the  
POWER key many times—possibly hundreds of times.  
6. Once you have found the correct code, you must  
save the new code by pressing and releasing the  
STOP key. The LED turns off. You must press the  
STOP key to save the code or the correct code will  
not be stored! When you press the STOP key, the  
code is stored.  
IMPORTANT: Remember to enter the code for future reference in  
the box provided in the Code Retrieval section of this manual. (See  
page 5.)  
7. Be sure to retrieve the code your remote programmed by  
finishing the Code Retrieval process found on page 5.  
Programming the DVD•VCR Key to Control a VCR or DVR  
The DVD•VCR key defaults to control a DVD player. If you want the DVD•VCR key to control a VCR or DVR, you must  
preprogram the DVD•VCR key.  
1. Press and hold the DVD•VCR key. The LED turns on. Keep holding down the DVD•VCR key.  
2. While holding down the DVD•VCR key, press and release the number 2 key on the keypad. The LED turns off.  
3. Release the DVD•VCR key. The LED blinks four times and then turns off. The DVD•VCR key is now “set” to control a VCR or DVR.  
4. Next, program the DVD•VCR key to control the brand of VCR you have. Remember to consult the VCR or DVR code list.  
3
 
5. Press and release the PLAY key, then wait five  
seconds to see if your component turns off. If  
your component does not respond, continue to  
press the PLAY key every five seconds until your  
component turns off.  
TestingtheCodeforMaximumFunctionality  
Different remote control codes can provide different levels  
of functionality. To confirm that the component key is  
programmed with the correct code for maximum functionality,  
follow the steps below.  
Each time you press the PLAY key, the LED blinks several  
times and a block of 10 codes are sent to your component.  
This process continues until all of the codes in the Code Lists  
have been searched. If your component has not turned off  
after all codes have been searched, the LED blinks four times  
and turns off. The Auto Code Search Entry method is exited.  
1. Attempt to control a variety of the component’s functions  
with the remote. If some features of your components do  
not work, go to step 2 to try a different code.  
2. Repeat the Manual Code Search and Entry Method from  
step 1. When the component turns off for the first time,  
do not press the STOP key, which would store the code.  
Instead, with the unit now off, continue to press the  
POWER key repeatedly until the unit turns back on.  
6. When your component turns off, you know the  
correct code is in the last block of 10 codes sent.  
Press and release the REVERSE key. Wait two  
seconds to see if your component turns on again.  
3. Once the unit turns back on, you have found another code  
that operates the component. Press the STOP key.  
If your component does not respond, continue to press the  
REVERSE key every two seconds until your component  
turns on again. This will isolate the correct code in the last  
block of codes sent. Each time the REVERSE key is pressed,  
the LED blinks.  
4. Test the key’s functionality again by attempting to control  
a variety of the component’s functions. If the code that  
has been stored controls the majority of the component’s  
functions, programming is complete. If the code stored does  
not give maximum functionality, try another code.  
Note: If you accidentally press the REVERSE key after your  
component responds, press and release the FORWARD key. Then,  
wait two seconds to see if your component turns off again.  
5. Repeat the Manual Code Search and Entry Method from  
step 1. Each time a code turns the component on or off, you  
have found a code that operates the remote and needs to be  
tested for maximum functionality. Continue through the  
code lists, cycling through the codes you have already tried,  
until you find one that offers maximum functionality.  
7. Once your component turns on, you have found  
the correct code. You must save the new code by  
pressing and releasing the STOP key. The LED  
turns off. When you press the STOP key, the code  
is stored.  
IMPORTANT: You must press the STOP key to save the code or the  
correct code will not be stored!  
Auto Code Search and Entry  
The Auto Code Search and Entry Method enables the remote  
to automatically search through all the codes in the Code Lists  
for the one that operates your component.  
8. To confirm that the component key is programmed with  
the correct code for maximum functionality, it is necessary  
to test the component. If some of the features of your  
component do not work, different codes in the list can  
be tried until you find the code that allows the remote  
to control the majority of your component’s functions.  
See the section entitled “Testing the Code for Maximum  
Functionality” below for more information.  
Note: The Auto Code Search method may take a long time because  
the remote searches through all of the codes in its memory for the code  
that operates your component. Therefore, if your brand is listed in the  
Brand Codes or the Code Lists, first try the Brand Code Search or the  
Direct Code Entry method described on pages 2–3.  
TestingtheCodeforMaximumFunctionality  
Different remote control codes can provide different levels  
of functionality. To confirm that the component key is  
programmed with the correct code for maximum functionality,  
follow the steps below.  
TIP: To exit without saving at any point in the Auto Code  
Search, press and release the CLEAR key.  
1. Manually turn on the component you want the remote to  
control (TV, VCR, DVD, DVR, satellite receiver, or cable box).  
1. Attempt to control a variety of the component’s functions  
with the remote. If some features of your components do  
not work, go to step 2 to try a different code.  
Note: To program the DVD•VCR key to control a VCR or DVR,  
see page 3.  
LED  
2. Press and hold the component key  
(TV, SAT•CBL, DVD•VCR) you  
wish to program. The LED turns on  
and remains on. Keep holding down  
the component key.  
2. Repeat the Auto Code Search Method from step 1. When  
you’ve found the code that turns your component back  
on, do not press the STOP key, which would store the  
code. Instead, with the unit now on, continue to press the  
REVERSE key repeatedly until the unit turns back off.  
Note: If you cannot find another code in this block that works, press the  
PLAY button to continue searching through the code blocks. When the  
component turns off again, press the REVERSE key to find the code in  
that block that makes your component turn back on.  
3. While holding the component key down, press and hold the  
POWER key. The LED turns off. After holding down both  
keys for three seconds, the LED turns back on.  
3. Once the unit turns back on, you have found another code  
that operates the component. Press the STOP key.  
4. Release both keys. The LED remains on.  
4. Test the key’s functionality again by attempting to control  
a variety of the component’s functions. If the code that  
has been stored controls the majority of the component’s  
functions, programming is complete. If the code stored does  
not give maximum functionality, try another code.  
Note: If you press an invalid key during Auto Code Search, the  
remote does not respond and the search times out after two minutes.  
When the search times out, the LED blinks four times and turns off.  
The last programmed code under that component key is retained.  
TIP: Throughout the programming of each key, be sure to keep the  
remote pointed at the IR sensor of the component you are currently  
programming the remote to control.  
5. Repeat the Auto Code Search Method from step 1. Each  
time a code turns the component on or off, you have found  
a code that operates the remote and needs to be tested for  
maximum functionality. Continue through the code lists,  
cycling through the codes you have already tried, until you  
find one that offers maximum functionality.  
 
Code Retrieval  
Using the Remote to Control  
Your Components  
Because this remote controls more than one component, you  
must first “tell” the remote which component you wish to  
operate. That means, if you wish to operate your TV, you must  
first press the TV key to put the remote in the TV Mode.  
Once you’ve programmed the remote to control your  
components, you may want to record the codes for future  
reference. If you used the Direct Code Entry method, this  
is easy. Just find the codes you entered and make a note of  
them in the boxes below. If you used one of the Code Search  
methods to program your remote or if you used the Direct  
Entry method but don’t remember the code, you will need to  
retrieve each component’s four-digit code. Retrieving the actual  
code and writing it down will save you time if you ever need  
to program the remote again (e.g., if programming is lost when  
you change the batteries). If the codes are recorded, you can use  
the Direct Entry method to reprogram your remote to control  
your components, which is quick and easy.  
The remote stays in the chosen component mode (such as TV  
Mode) until you change it. If your remote is in TV Mode, you  
must change the mode in order to operate your DVD, VCR,  
DVR, auxiliary component, satellite receiver, or cable box. For  
example, if you are in DVD Mode, and you wish to turn off  
your TV, you must press the TV key first before pressing the  
POWER key.  
LED  
1. Press and hold the component key  
(TV, SAT•CBL, DVD•VCR) whose  
code you wish to retrieve. The  
LED turns on. Keep pressing the  
component key.  
Accessing Component Menus  
and Guides  
Today’s advanced components use on-screen menus and  
guides to help you navigate through all their features and  
programming. While this remote may not access every menu  
or guide system of every component model, it does offer some  
menu and guide functionality.  
2. While holding the component key down, press and hold  
the INFO key. The LED turns off. After holding down both  
keys for three seconds, the LED turns back on.  
To use a component’s on-screen menu or guide system, you  
first have to put the remote in Menu or Guide Mode.  
3. Release both keys. The LED remains on.  
4. Starting with the number 1 key, press and release each  
number key on the keypad in the following order (1-9, then  
0). The number that causes the LED to blink is the first  
number of the code. As you find each number of the code,  
write it down for future reference.  
1. Make sure your components are turned on and your TV  
is set to a component input (Use the INPUT key to toggle  
through inputs when in TV Mode.)  
LED  
2. Press the component key whose  
menu you want to access.  
Note: All TV codes begin with the number 1; all VCR and DVR  
codes begin with the number 2; all DVDs, the number 3; and all  
satellite receivers and cable boxes, the number 5.  
3. To access menus, press the MENU  
key. To access guides, press the  
GUIDE key. The LED blinks,  
indicating you are in Menu or  
Guide Mode.  
5. Repeat step 4 until you have retrieved all four numbers in  
the code. After the fourth number is retrieved, the LED  
blinks briefly, then turns off.  
TIP: To exit the Code Retrieval Mode, press and release the  
CLEAR key at any time.  
4. Use the arrow keys to navigate  
through the on-screen menu  
system or guide. To select the  
highlighted item, press the MENU  
or OK key.  
Note: If you press an invalid key during the Code Retrieval process,  
the remote will not respond. If you do not press a valid Code  
Retrieval key (TV, SAT•CBL, DVD•VCR, INFO, CLEAR),  
Code Retrieval times out after 15 seconds. The LED blinks four  
times, and then turns off.  
TIP: If the remote doesn’t respond, check to see that the LED is still  
blinking. The LED times out after 20 seconds. If this happens, just  
press the MENU key again, and then retry your selection.  
TV Code  
SAT•CBL Code  
Exiting a Menu Mode  
The remote automatically times out of Menu Mode after 20  
seconds of inactivity (no keys being pressed). At that time, the  
remote clears the displayed menu from the TV.  
1
5
SAT  
CABLE  
If you want to exit the Menu Mode yourself, press the  
corresponding component key on the remote (TV, SAT•CBL,  
DVD•VCR). The LED turns off.  
dVd•VCR Code  
DVD  
VCR  
 
Problem: The VCR won’t record.  
Troubleshooting  
Make sure the remote is in DVD•VCR Mode.  
Make sure the tape is properly loaded in the VCR.  
Problem: The remote does not operate your component.  
You must put the remote in the correct mode by pressing the  
corresponding component key (TV, SAT•CBL, DVD•VCR) so the  
remote knows which component you want to operate.  
Make sure the tape is not write-protected. If the safety tab is  
removed the tape is write-protected, and you cannot record onto  
that tape.  
Remove any obstacles between the remote and the component.  
Make sure to aim the remote at the IR sensor on the component.  
Make sure the batteries are fresh and are properly installed. (See  
Battery Installation on page 1.) Replace the batteries with two new  
AAA batteries, if necessary. Reprogramming may be required.  
Reset the remote. Remove the batteries, then press and hold  
the number 1 key on the remote for several seconds to reset the  
microprocessor inside the remote. Release the number 1 key,  
reinstall the batteries, and press the POWER key. If the LED lights  
up, reprogram the remote and try again. If the LED doesn’t light  
up, replace the batteries with new ones.  
Problem: The remote will not change channels on  
component.  
You must put the remote in the correct mode by pressing the  
corresponding component key (TV, SAT•CBL, DVD•VCR) so the  
remote knows which component you want to operate.  
Press the ENTER key after you enter a channel number.  
Remove any obstacles between the remote and the component.  
Make sure to aim the remote at the IR sensor on the component.  
Problem: The component’s menu does not appear on the  
TV screen.  
Problem: The remote can’t be programmed to operate  
your component.  
Make sure you have connected your component to your TV  
properly and selected the correct input. (See your components’  
Owner’s Manuals for proper connection procedures.)  
If you are testing the remote after you have entered the code, you  
may be too far away from the component or at a wrong angle.  
This remote uses IR (infrared) technology to communicate with  
components. The remote sends the code, and the component’s IR  
sensor reads the code. Therefore, there must be an unobstructed  
path between the remote and the IR sensor on the component.  
Move closer and make sure you point the remote at the  
You must put the remote in the correct mode by pressing the  
corresponding component key (TV, SAT•CBL, DVD•VCR) so the  
remote knows which component you want to operate.  
Menu access isn’t supported for all brands. If that’s the case, you’ll  
need to use your original remote control to access menu functions  
for these components.  
component (DVD player or VCR when programming the  
DVD•VCR key; TV when programming the TV key; satellite or  
cable box when programming the SAT•CBL key).  
If you’ve used the Direct Entry programming methods to enter the  
codes for your brand and the unit is still not functioning properly,  
try one of the Code Search methods. (See pages 3–5.)  
Limited Lifetime Warranty  
Audiovox Electronics Corporation (the “Company”) warrants to you the  
original retail purchaser of this product that should it, under normal use  
and conditions, be proven defective in material or workmanship during its  
lifetime while you own it, such defect(s) will be repaired or replaced (at the  
Company’s option) without charge for parts and repair labor. To obtain repair  
or replacement within the terms of this Warranty, the product is to be delivered  
with proof of warranty coverage (e.g. dated bill of sale), specification of  
defect(s), transportation prepaid, to the Company at the address shown below.  
To control combo units, like TV/VCRs or TV/DVDs, you must  
program the individual corresponding component keys to control  
each part of the combo unit. Once programmed successfully,  
the TV key controls the TV functions, and the DVD•VCR key  
controls the VCR or DVD functions. There is a specific section in  
the Code Lists for combo units. The codes in this section should  
be tried first using Direct Code Entry on the TV and DVD•VCR  
keys. If this is unsuccessful, follow the normal programming  
methods for both the TV and the DVD•VCR keys.  
This Warranty does not cover product purchased, serviced or used outside the  
United States or Canada. This Warranty is not transferable and does not extend  
to costs incurred for installation, removal or reinstallation of the product.  
This Warranty does not apply if in the Company’s opinion, the product has  
been damaged through alteration, improper installation, mishandling, misuse,  
neglect, accident, or the simultaneous use of different battery types (e.g.  
alkaline, standard or rechargeable).  
Make sure the batteries are fresh and are properly installed.  
Problem: The remote doesn’t perform commands properly.  
You must put the remote in the correct mode by pressing the  
corresponding component key (TV, SAT•CBL, DVD•VCR) so the  
remote knows which component you want to operate.  
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS  
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT  
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S  
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER  
FOR THE PRODUCT.  
Make sure component is “ready” (e.g., DVD player has disc  
loaded; VCR has tape loaded, etc.).  
You may have pressed an invalid key for the mode the remote is in.  
This Warranty is in lieu of all other express warranties or liabilities. ANY  
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY  
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY.  
IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY  
CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. No  
person or representative is authorized to assume for the Company any liability  
other than expressed herein in connection with the sale of this product.  
If you’re trying to turn on an RCA, GE, or PROSCAN  
component, press the component key (TV, SAT•CBL, DVD•VCR)  
instead of the POWER key.  
If you’re trying to enter a channel number directly, try pressing  
the ENTER key after entering the channel number as this is a  
requirement of certain models and brands.  
There is a possibility that a programmed code may only be able  
to control some of your component features (e.g., only turns a  
component on and off). To confirm that the component key is  
programmed with the correct code for maximum functionality, test  
the component. Attempt to control a variety of the component’s  
functions with the remote. If some of the features of your  
components do not work, try programming the remote with a  
different code in the list using the Direct Code Entry Method,  
until you find the code that allows the remote to control the  
majority of your component’s functions. Different codes can  
provide different levels of functionality.  
Some states/provinces do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential  
damage so the above limitations or exclusions may not apply to you. This  
Warranty gives you specific legal rights and you may also have other rights,  
which vary from state/province to state/province.  
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,  
New York 11788  
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,  
Unit 3, Door 16, Mississauga, Ontario L5T 3A5  
Problem: The LED does not light when you press a key.  
You may have pressed an invalid key for the mode the remote is  
in. You must put the remote in the correct mode by pressing the  
corresponding component key (TV, SAT•CBL, DVD•VCR) so the  
remote knows which component you want to operate.  
©2007 Audiovox Corporation  
Accessories Group  
ꢀꢀꢀ Congressional Blvd., Suite 3ꢂ0  
Carmel, IN ꢁꢃ032  
Trademark(s) ® Registered  
RCR3283 US 02  
Make sure the batteries are fresh and are properly installed. (See  
Battery Installation on page 1.) Replace the batteries with two new  
AAA batteries, if necessary. Reprogramming may be required.  
RCR3383 US 02  
 

Razor Pet Fence 10067112 User Guide
RedMax Tiller CV225 User Guide
Regency Indoor Fireplace U27 LP1 User Guide
RIDGID Drill SP6490 User Guide
Roland Electronic Keyboard EP 760 User Guide
Sakar Digital Camera 14097 User Guide
Samsung Air Conditioner AD18A1B1E09 User Guide
Samsung All in One Printer SCX 5835FN User Guide
Samsung Flat Panel Television LE26R41BD User Guide
Schumacher Battery Charger MKC 10P User Guide