Q See Digital Camera QD113P User Guide

SETTING DATE & TIME  
PARTS  
OPERATION  
INTRODUCTION  
To ensure that your camera records the proper  
date and time on the files, you should run the  
Setting Time Tools V2.0 program located in the  
folder of the same name on the included mini-CD.  
1. Operation Button  
CHARGING  
Thank you for your purchase of the Q-See QD113P  
Portable Surveillance Device. This versatile tool is  
built around an ultra-mini camera which combines  
1.3-megapixel still photography and high-resolution  
real-time video with audio in a compact, discrete  
package. Store nearly 4,000 pictures or 2 hours of  
video on the internal 4GB memory. View or save  
your files on any PC with a USB port. Recharge the  
pen with the included charger or from a computers  
USB port. The ease of use, small size and el-  
egant design make this a valuable tool for security  
personnel, business people, students, tourists and  
others.  
The pen features a high-capacity rechargable  
lithium polymer battery. This form of battery does  
not have a “memory” effect meaning that it can  
be recharged at any time without loss of capacity.  
However, it is recommended that you fully charge  
the battery and then use the camera normally until  
it is fully discharged before recharging. Cycling the  
battery in this manner for the first five times will  
ensure maximum battery capacity and operation  
time.  
2. Status indicator light  
3. Camera lens  
When the program launches, a Command window  
will open and the program will update the date and  
time based on your computers settings.  
4. Microphone  
(behind pocket clip)  
5. Reset button  
6. USB plug  
When charging the battery – whether using the  
included charger, or plugged into an active USB  
port – the status light will flash yellow/amber until  
the battery is fully charged. During the first few  
uses, allow the pen to continue charging for an  
hour after the light stops flashing.  
Depending upon your computers settings, you  
may see a warning about the pens drive not  
being available. The warning is normal as the  
program re-mounts the pen. Click “Continue” and  
the status of the update will be displayed in the  
Command window. Keep clicking “Continue” until  
you see the “Success” message in the window.  
Your pen now is set to the proper date and time.  
7. Mode Switch  
Left = Video  
Right = Still Image  
When using the charger, both the green and red  
lights will illuminate until the battery is fully charged.  
When fully charged, only the red light will remain  
illuminated.  
8. Ball-point pen  
STILL IMAGE CAPTURE  
VIDEO RECORDING  
PEN  
HELPFUL HINTS  
Rotate the metal collar at the tip to  
extend or retract the writing nib.  
1. Move the Mode Switch to the  
left (use the pens tip if needed).  
• When taking pictures, you will get the best  
results if both you and your subject are relatively  
still.  
1. Move the Mode Switch to  
the right (use the pens tip if  
needed.)  
2. Press the Operation Button for  
1 second. The Status Indicator  
light will briefly illuminate  
amber before switching to blue  
indicating that the camera is  
recording.  
• The camera should be at least one foot from  
your subject when taking pictures.  
2. Press the Operation Button for  
1 second. The Status Indicator  
light will briefly illuminate amber  
before switching to the blue  
“Ready” status.  
USB DRIVE  
The pen can be used as a standard USB Flash  
memory stick for transporting and transferring files.  
• While recording video, you should try to keep  
the camera steady and avoid rapid movements  
for best video quality.  
3. Press the Operation Button  
again to end the recording. The  
INSUFFICIENT MEMORY OR BATTERY  
3. Press once on the Operation  
Button to take a picture. The  
Status Indicator light will briefly  
flash amber in addition to the  
steady blue. The camera is  
ready to take another picture.  
You should not hold the pocket clip while taking  
video in order to avoid blocking the microphone  
or lens.  
When the cameras memory is full or the battery  
has run out of power, the Status Indicator light will  
alternately flash amber and blue for five seconds.  
It will then save the current file and shut down. You  
must remove the files stored on the memory to  
make space available to record further or recharge  
the battery as appropriate.  
Powering Up  
Ready  
Status Indicator light will switch  
from blue to amber indicating  
that the recording has been  
saved and the camera is now on  
“standby” and ready to record  
more video.  
Powering Up Recording  
4. To turn off the camera, press  
and hold the Operation Button  
until the Status Indicator light  
goes off. To conserve energy,  
the camera will automatically  
turn off after a few minutes of  
inactivity as well.  
4. To turn off the camera, press  
and hold the Operation Button  
until the Status Indicator light  
goes off. To conserve energy,  
the camera will automatically  
turn off after a few minutes of  
inactivity as well.  
Standby  
Recording Image  
 

PYLE Audio Speaker PLBASS8 User Guide
Radio Shack Cordless Telephone 43 3815 43 3898 User Guide
Raritan Computer Battery Charger 23 422 User Guide
Rolls Stereo Receiver ADB3b User Guide
Rosewill Computer Drive RX20 U2 User Guide
Samson Musical Toy Instrument M32 User Guide
Samsung Cell Phone C414 User Guide
Sanyo Computer Monitor CE42WPX1 User Guide
Sanyo Computer Monitor VMC L2617 User Guide
Sears Saw 113244501 User Guide